OSI GS121 Gutter & Seam Seal - 10 oz Butyl-rubber goo that bonds to damp aluminum, flexes from 20 °F to 120 °F, and cures in 30 minutes. Run a ¼-inch bead inside leaking miters or end-caps - goodbye drip lines.
Gutter repair tools for Buford, GA
One crooked spike, one pin-hole seam, and a Georgia downpour can turn your porch into a splash park. Luckily, you don’t need high-priced gimmicks to make gutters watertight again - just a handful of hardware-store heroes that fit in a five-gallon bucket.
We’re a roll-up-the-sleeves roofing shop - no spotless box trucks, no laser levels - so every tool below has earned its place tossing rain off Buford roofs from historic downtown cottages to subdivision two-stories. Patch today, smile tonight, and keep repair money for weekend barbecue.

Leaks start tiny - fix them tinier
Floppy hanger, rusty corner, loose spike. Ignore any one of them and water sneaks behind fascia, soaks soffits, and feeds mold quicker than hot bread molds in July heat. Call a pro after wood rot shows up and you’ll sign a check with too many zeros.
Why our toolbox stays small: * Affordable - each item cheaper than a pizza combo. * Available - pick up at Buford Home Depot tonight, fix tomorrow. * Forgiving - no specialty skills; if you can run a drill, you can run these.
Work once, rest easy: Spend one noon hour sealing seams and swapping saggy hangers, and you’ll dodge paint jobs, drywall patches, and crawl-space dehumidifier bills for years.
OSI GS121 Seam Seal - sticks in drizzle
2-in-1 hanger + screw pack - lift sag in seconds
Raytec Hangtite Hidden Hangers - 50 ct Aluminum bracket with pre-mounted #10 ceramic screw. Slide under the lip and drive - five per ten feet keeps heavy Georgia rain from bowing the run.
Swivel-head rivet gun - tight corners, no knuckle bangs
Astro 1423 Swivel Riveter Rotates 360°. Pop two 1/8" aluminum rivets in every inside miter - corner stays square, sealant stays lazy.
Offset snips - trim patches without burrs
Midwest Offset Aviation Snips (Left & Right) Forged blades cut .032" aluminum patches or downspout sleeves clean, keeping fingers above sharp edges.
Sheet-metal patch roll - instant Band-Aid for holes
Amerimax Aluminum Flashing Roll - 6" × 10 ft Snip a 4" square, scuff with sandpaper, butter with GS121, press from inside trough - leaks disappear.
6" square-drive bit - no stripped heads
Irwin #2 SQ Power Bit - 6 in Long reach clears gutter wall; chamfered tip means screw heads live to fight another storm.
Downspout band tool - stop the rattle
Pentair Band-Tight Tool Cinches pre-punched straps tight around 3" × 4" spouts - no more clanging when strong winds roar.
Quick-scan checklist: find leaks before they spread
Doing a quick walkaround can save you hundreds down the line. No need for drones or thermal cameras - just sharp eyes and a steady ladder.
• Stains on siding just below a gutter seam usually mean water’s seeping through and running down the wall. That can lead to mold inside if ignored.
• Soft or mushy fascia when gently poked with a screwdriver? That means water’s been getting behind the gutter and soaking the wood.
• Weeds or grass growing in corner joints? That’s dirt buildup from slow leaks. Where there’s soil, there’s moisture - and leaks love company.
• Loose screws or wiggly spikes are often overlooked, but they tell you the whole run might be pulling away from the house.
See one of these red flags? Don’t wait. Grab your bucket, grab your scoop, and get to it - because today’s a whole lot cheaper than next week after a thunderstorm.
Five-step patch: 30-minute fix for pin-hole drips
Tiny leaks might not seem like much, but over time they’ll rot out wood, attract ants, and streak your siding. Good news is - they’re easy to fix with basic supplies.
- Clean the area at least 6" around the drip. A rag and a splash of dish soap will do. Dry with an old towel - sealant hates moisture.
- Rough up the surface using a scrap of 120-grit sandpaper. Gutter metal is slick, and sealant needs something to grip.
- Cut a small patch from aluminum flashing about 1" bigger than the hole in all directions. Don’t worry about fancy shapes - square works just fine.
- Apply GS121 sealant thick on the back of the patch. Press it into the gutter bottom and smear a bead around the edge with a gloved finger.
- Pop two rivets in each corner. That patch isn’t going anywhere. Wipe away extra sealant. Done.
Simple, strong, and stops the drip before it gets expensive.
Sag-lift routine: tighten run before water swims uphill
When gutters sag in the middle, water starts backing up instead of draining - and suddenly, you've got a water pool over your door.
• Snap a chalk line underneath the gutter from end to end. This shows you where the run should be - it’s more honest than your eyes.
• Add hidden hangers every two feet wherever you see the gutter dipping below the chalk line.
• Use a cordless drill and drive the screws snug - but not too tight. You want firm contact, not crushed metal.
• Re-check your slope. Rule of thumb is 1/4" drop for every 10 feet. That’s enough to keep Georgia’s wild summer rains moving without dumping water over the edge.
This job takes less than an hour and keeps your system flowing like it should.
Corner rebuild: seal + rivet + paint
Inside corners (or miters) are the first spots to go bad. They take on the most water and usually have the most seams. Here’s how to give them a new life - no fancy tools, just patience.
• Start by scraping out the old caulk or sealant. A plastic scraper works best so you don’t gouge the aluminum.
• Drill out any old rivets with a small bit - go slow so you don’t warp the joint.
• Wipe the area clean with rubbing alcohol. That removes dirt and oils so the new sealant sticks right.
• Run a fresh bead of GS121 (or your go-to exterior sealant) around the inside edge. Press the miter pieces together, clamp if needed.
• Add four rivets - one per side, per seam. Then wipe the seam smooth with a gloved finger.
• Optional: dab a little touch-up paint over the repair to blend it in and protect from UV damage.
You’ll get at least another 10 years out of that corner with this simple fix.
Seasonal rhythm: light touches, big savings
You don’t need to baby your gutters every month - but a few light checkups each season make a huge difference.
Spring - Georgia pollen cakes everything. Check for seams leaking yellow streaks and tighten any hangers loosened by winter wind.
Summer - Before hurricane season, double-check all downspout straps. Heavy rains and high winds will find every weakness. Re-check pitch with a level if you see standing water.
Fall - Once the last leaves drop, do a full cleanout. Scoop, flush, inspect corners, and seal anything questionable before winter sets in.
Winter - If you see icicles, don’t ignore them. They’re not just pretty - they mean your gutters might be clogged or pitched wrong. Clear them fast before freeze damage spreads to your fascia.
Do this and you’ll avoid big repairs with just a little time and effort.
Safety corner: common-sense beats fancy helmets
Roof work doesn’t need to be dangerous - but it does demand respect. No hard hat required, just these five good habits:
- Use a ladder stabilizer - don’t let your boots rest on the gutter lip. One slip can ruin more than just your day.
- Wear gloves and safety glasses. Metal edges, wasps, and flying debris are not your friends.
- Use a bucket on a rope. Hoist tools after you climb, not while holding them in your hand.
- Stay hydrated. Even in mild weather, rooftops heat up fast and sneak up on you.
- Always text someone when you go up and when you’re down. Roofs are quiet places, and accidents can happen fast.
Simple steps, serious safety. Keep yourself and your job site clean, dry, and injury-free.
Tool care: keep rust off, keep wallets full
Good tools aren’t cheap - but if you treat them right, they’ll outlast the truck.
• Wipe your snips with a rag and a little WD-40 after any job that involves caulked metal. That residue builds up fast.
• Fire your rivet gun with a drop of oil, then store it with the jaws open. Keeps springs healthy.
• Sealant tubes should be stood upright in a zip-top bag. When reusing, just snip the tip a bit lower and keep going.
• Coil your cords in a figure-eight loop to avoid kinks and tangles. Saves frustration next time you pull them out.
• Use a Sharpie to write today’s date on each handle - just a simple way to track age, wear, and next clean.
Five minutes of care saves hours of hassle - and a trip to the store you didn’t want to make.
Patch today - enjoy tomorrow’s rain
Whether you're in historic downtown Buford or a busy cul-de-sac, these down-to-earth tools turn gutter leaks into easy wins. Stock the bucket, follow the steps, and keep Buford showers outside where they belong. Need a hand? We’re a phone call and a friendly pickup ride away.
Shop Gutter Repair Kits- Phone: (470) 888 0030
- Address: Buford, GA